Failing Jet Action. When your Marquis hot tub won't bubble properly, there likely is a problem with the jets. Check the shut-off valves in the tub's equipment area to ensure they are fully open. Examine the jets themselves and turn the jet face to permit maximum water flow. We are a wholesale distributor of spa and hot tub parts. Marquis Spa Owners Manuals. Hideaway Hot Tubs. Marquis Spa/ Hideaway Hot Tubs Owners Manual.
Below are some of the most common spa side error codes and there possible causes. For the complete list of error codes.
For further troubleshooting. If you are unsure of something or have any questions, please do not hesitate to contact us via. Sending a digital picture is very helpful in helping us to troubleshoot or answer any questions. • FLO, FL, FLC, FL1, PS, Blinking Lights Pressure Switch or Flow Switch Failure. The codes above are all related to flow issues or the pressure switch/flow switch and are the most common error codes. These error codes can be caused for several different reasons.
The main reason is water flow through the spa control system, if water is not flowing at a rate to satisfy the pressure switch, it will result in one of the error codes above. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.
Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way.
It also gave the group their biggest hit in the United States, where it peaked at number 30 on the and was certified gold by the RIAA. The prodigy discography torrent. '', the album's first single, peaked at number one in the United Kingdom and hit the top ten in multiple other countries. The album's second single '' also performed well commercially, reaching the top ten in multiple countries and becoming the group's second consecutive UK number-one hit.
The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open all the way, you may need to dismantle the fittings to look inside. The final problem could be the pressure switch/flow switch itself.
You can check the switch by performing the test below. Shut the power down, remove the two wires to the pressure switch/flow switch, find some sort of wire to join the wires, but don't do it yet. Turn the power back on, you have five seconds to join the wires together, do not join them before you turn the power on. Once this is done check ACROSS the heater element post, you should have either 110 volts or 220 volts depending on what voltage is operating the control box.
If the error code goes away and you are getting the proper voltage then replace the pressure switch/flow switch. Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires. FINAL NOTE: Most spas are equipped with and can be found threaded into the stainless steel heater manifold. Are plumbed in line with the plumbing. You can also check the pressure switch or flow switch with a an Ohm meter.
When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. • OH, OHH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights Temperature Sensor Failure. The error codes above are related to a temperature sensor failure, overheat problems or a flow problem.
If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate the heater are stuck shut causing and over heat issue, in this case you would need to either replace or repair the circuit board. For information regarding repairs click If your spa is not overheating and you are getting the above error codes then a couple of things could be happening. Depending on where the temp sensor is mounted; usually in the wall of the spa in a, you could have a flow issue. Shut the spa down, remove the filter and make sure all the jets are open.
Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced. NOTE: Temperature sensors should be mounted in a sensor mount in the wall of the spa and not behind the shield on the heater manifold with the hi limit sensor.