Mar 17, 2015 - Upcmcv7 4 Keygen Download UPCMCv126.96.36.199 R3 crack direct download link (click and install) UPCMC Panasonic PBX Unified Maintenance.
• Please read this manual carefully before using this product and save this manual for future use. In particular, be sure to read '1.2 For Your Safety (Page 5)' before using this product. KX-NS500: PFMPR Software File Version 004.20000 or later. Manuals and supporting information are provided on the Panasonic Web site at: • Table of Contents Table of Contents 1 Before Installation.3 Outline..4 For Your Safety..5 Unpacking..7 2 Installation..9 Opening/Closing the Top Cover.10 Installing DSP Cards..12 Frame Earth Connection..14 LAN Connection..14 2.4.1 LAN Connection for the Main Unit.14 2.4.2 LAN Connections for IP Telephones.16 Connecting Extension..18. • Section 1 Before Installation Getting Started. • Third party SIP phone (SIP hardphones/SIP softphones) • Operation of the KX-NS0154 depends on the PBX software file version and the firmware version of the KX-NS0154. You can confirm the compatibility on the Panasonic Web site: About the Other Manuals User Manual Provides operating instructions for end users using IP-PTs, SIP phones, SLTs, PSs, or DSS Consoles.
• 1.2 For Your Safety 1.2 For Your Safety To prevent personal injury and/or damage to property, be sure to observe the following safety precautions. The following symbols classify and describe the level of hazard and injury caused when this unit is operated or handled improperly. • 1.2 For Your Safety WARNING • Proper earthing (connection to earth) is very important to reduce the risk to the user of electrocution or to protect the PBX from the bad effects of external noise in the case of a lightning strike. • 1.3 Unpacking 1.3 Unpacking Check the package contents. KX-NS500 Main Unit ´ 1 (including manuals, etc.) ´ 1 CD-ROM AC power cord Hook clip 19-inch rack attachment bracket x 2 Screw x 6 (For 19 inch rack) Screw x 3 (For Wall Mounting) Washer x 3 (For Wall Mounting) The number of included CD-ROMs varies according to the country/area. • 1.3 Unpacking Getting Started.
• Section 2 Installation Getting Started. • 2.1 Opening/Closing the Top Cover 2.1 Opening/Closing the Top Cover Opening the Top Cover KX-NS500/KX-NS520 CAUTION Before opening the top cover, the AC power cord must be removed from the AC inlet. Confirm that the power switch is turned off and disconnect the power cable. • 2.1 Opening/Closing the Top Cover Slide the top cover then lift it off. Closing the Top Cover Place the top cover onto the PBX. Then slide the top cover until it closes properly.
Turn the screws clockwise to tighten. CAUTION For safety reasons, close the top cover and tighten the screws before operating the PBX. • 2.2 Installing DSP Cards 2.2 Installing DSP Cards CAUTION • Before touching the product (PBX, cards, etc.), discharge static electricity by touching ground or wearing an earthing strap. Failure to do so may cause the PBX to malfunction due to static electricity. • 2.2 Installing DSP Cards Depending on the amount of your DSP resource needs, a DSP S, DSP M, or DSP L card can be installed.
In order to use VoIP features with the PBX, a DSP S, DSP M, or DSP L card must be installed in the DSP card slot. • 2.4.1 LAN Connection for the Main Unit 2.3 Frame Earth Connection KX-NS500/KX-NS520 Loosen the screw. Insert an earthing wire (user-supplied). Tighten the screw. Connect the earthing wire to earth. Anjos da lei 2 download dvdrip legendado. Screw Earthing wire To earth WARNING • Proper earthing (connection to earth) is very important to reduce the risk to the user of electrocution or to protect the PBX from the bad effects of external noise in the case of a lightning strike. • 2.4.1 LAN Connection for the Main Unit Connect the other end of the cable to the switching hub.
IP Softphone, CTI Server CA Client PC LAN Port Switching Hub Ethernet Cable IP-PT IP-CS SIP-CS Trunk Adaptor SIP Phone Connection for 10BASE-T/100BASE-TX Switching Hub PBX (LAN Port) Pin No. • 2.4.2 LAN Connections for IP Telephones 2.4.2 LAN Connections for IP Telephones When an IP telephone is connected to the LAN and power is supplied for the first time, you will be prompted to set network parameters. The network parameters must be set for the IP telephone before it can be used. Refer to '4.3 Assigning Networking Information to IP Telephones'. • 2.4.2 LAN Connections for IP Telephones Connecting an AC Adaptor to an IP Telephone IP-PTs and some SIP phones comply with the IEEE 802.3af Power-over-Ethernet (PoE) standard. If PoE is available on your network, these IP telephones can receive the necessary power supply from the network through the network cable.
• 2.5 Connecting Extension 2.5 Connecting Extension To DPT To SLT Regarding of the PIN assignment of RJ45 (PBX side), refer to the Installation Manual. Example: KX-DT300 Series DPT Pin Assignments DPT and DSS Console TO MAIN UNIT / PABX KX-T7000 Series SLT Getting Started. • Section 3 Before Programming Getting Started. • 3.1 Starting the PBX 3.1 Starting the PBX WARNING Make sure that the AC outlet is properly earthed, then securely connect the 3-pin AC plug including the earthed pin. CAUTION • Use only the AC power cord included with the PBX. • 3.1 Starting the PBX Connecting the AC Power Cord Plug the AC power cord into the PBX and pass the cord through the hook clip as indicated.